API-570 Exam PDF [2024] Tests Free Updated Today with Correct 150 Questions
API API-570 Exam Preparation Guide and PDF Download
API-570 exam covers a wide range of topics related to piping inspection, including inspection procedures, materials, damage mechanisms, corrosion control, and repair methods. To be eligible to take the exam, candidates must have relevant experience in piping inspection and meet specific educational requirements. Those who pass the exam can demonstrate their ability to inspect and evaluate piping systems and can help ensure that these systems are safe and reliable.
NEW QUESTION # 23
What should have been the correct number and type of guide bends on the PQR?
- A. 2 face and 2 root bends
- B. 1 side, 1 face and 1 root bend
- C. 6 side bends
- D. No side bends required
Answer: D
NEW QUESTION # 24
Is the attached PQR properly qualified?
- A. No, because RT is not allowed during PQR qualification
- B. Yes
- C. No, because peening is allowed by ASME B31.3
- D. No, because there are not enough tensile tests
Answer: D
NEW QUESTION # 25
The radiograph of a Normal Fluid service piping weld revealed a crack.
What is the acceptable crack length if the pipe wall was 0.375?
- A. 3/16"
- B. None
- C. T/3
- D. Cracks will not show on radiographs
Answer: B
NEW QUESTION # 26
Penetrameters are normally placed on the side of the part being examined.
- A. source
- B. film
- C. weld
- D. reverse
Answer: A
NEW QUESTION # 27
For 1 1/4" thick carbon steel, what is the recommended preheat temperature?
- A. 175°F
- B. None
- C. 235°F
- D. 300°F
Answer: A
NEW QUESTION # 28
provides general requirements and detailed assessment procedures for specific types of degradation that are referenced in API 570.
- A. API 653
- B. API RP 579
- C. API 598
- D. ASME 816.5
Answer: B
NEW QUESTION # 29
The transmitted film density through the radiographic image of the body of the appropriate hole penetrameter and the area of interest shall be minimum for radiographs made with a gamma ray source.
- A. 2.0
- B. 2.2
- C. 2.6
- D. 1.8
Answer: A
NEW QUESTION # 30
A DC yoke shall have a lifting power of at least
- A. 40 lbs.
- B. 10 lbs.
- C. 8 lbs.
- D. 5 lbs.
Answer: A
NEW QUESTION # 31
Penrtrameters (IQls) shall either be____or_____and shall be manufactured and identified in accordance with ASME.
- A. black-type white-type
- B. hole-type wire-type
- C. pica-type elite-type
- D. step wedge calibration block
Answer: B
NEW QUESTION # 32
Exemptions for preheating and post weld heat treatment must be approved by the____.
- A. repair procedure.
- B. applicable standard, API 570
- C. inspector
- D. piping engineer
Answer: D
NEW QUESTION # 33
Care should be taken not to during a pressure test.
- A. use water in the system
- B. allow any inert gas into the system
- C. over-pressure the system
- D. under-pressure the system
Answer: C
NEW QUESTION # 34
An inspector is evaluating a radiograph, a light image of a "B" appears on a darker background of the radiograph, the.
- A. radiograph shall be considered unacceptable
- B. "B" is for identification of the welder
- C. radiograph should not be rejected
- D. "B" is for identification of the weld
Answer: A
NEW QUESTION # 35
Buried piping inspected periodically by excavation shall be inspected in lengths of:
- A. Any length as long as It IS Inspected full circumference.
- B. 3 feet -5. feet
- C. Any length as long as it is inspected 180° circumference.
- D. 6 feet -8 feet.
Answer: D
NEW QUESTION # 36
Geometric unsharpness of the radiograph of a component under 2" th1ck shall not exceed
- A. 0.050"
- B. 0.020"
- C. 0.040"
- D. 0.030"
Answer: B
NEW QUESTION # 37
A piping inspector employed by the owner operator shall have
- A. an API 510 certification
- B. not less than 10 years experience dealing with piping
- C. an AWS certification
- D. an API 653 certification
Answer: B
NEW QUESTION # 38
API 570 applies to piping systems for process fluids such as:
- A. Piping systems on trucks, ships and barges
- B. Firewater
- C. Raw, intermediate, and finished products.
- D. Plumbing, sanitary sewers and storm sewers
Answer: C
NEW QUESTION # 39
What is the maximum Brinell hardness of base metal P-6?
- A. 0
- B. 1
- C. not specified
- D. 2
Answer: A
NEW QUESTION # 40
API 570 covers the inspection of__________.
- A. new construction
- B. In-service vessels
- C. new tank construction
- D. In-service piping
Answer: D
NEW QUESTION # 41
Which of the following applies to socket welds in piping systems?
- A. Should be welded using SAW only
- B. Should be avoided
- C. Should be used in all welded piping
- D. Should be avoided where crevice corrosion may occur
Answer: D
NEW QUESTION # 42
The base metal is P No.1, the weld metal is A No.1, and the wall thickness is 7/8".
What is the holding time at 1100- 1200?F for heat treatment
- A. 1 hour
- B. 2 hours
- C. Procedure is not required for this thickness
- D. 3 hours
Answer: A
NEW QUESTION # 43
Welding repairs of cracks that occurred in-service should not be attempted without prior consultation with the
- A. plant manager
- B. inspector only
- C. piping engineer
- D. welding foreman
Answer: C
NEW QUESTION # 44
all suspect areas and areas of damaged insulation should be examined?
- A. 33%
- B. 10%
- C. 100%
- D. 50%
Answer: B
NEW QUESTION # 45
The three well-known methods of determining soil resistivity are, soil bar, soil box and______.
- A. A-C Bridge
- B. Wenner (4-pin) method
- C. holiday pipe survey
- D. six pin method
Answer: B
NEW QUESTION # 46
What is the maximum thickness measurement inspection interval for an injection point?
- A. 3 years
- B. 5 years
- C. By Class
- D. 10 years
Answer: A
NEW QUESTION # 47
A welder may be qualified by AT in any welding process except for which of the following?
- A. SMAW
- B. GMAW (spray arc mode)
- C. FCAW
- D. GMAW (short circuiting mode)
Answer: D
NEW QUESTION # 48
......
Verified & Correct API-570 Practice Test Reliable Source Jan 19, 2024 Updated: https://testprep.dumpsvalid.com/API-570-brain-dumps.html